Virat Special Steels
tuv
 

HXM 24 Steel

Choosing a mould steel is a balancing act. Too soft, and the cavity wears or dents early. Too hard, and machining time, tool cost and cracking risk all climb. Virat Special Steels supplies HXM 24 tool steel for plastic injection molds, extrusion tooling and precision dies. HXM 24 is a type of pre-hardened mold and tool steel used by customers who need a hard steel but do not want to have it hardened after machining. This guide discusses what HXM 24 is, its indicative chemistry and mechanical properties, how it machines and polishes, where it fits and what to check before you order.

What Is HXM 24 Tool Steel?

HXM 24 is a hard steel, pre-hardened tool steel which is required for operations which require hardness, wear resistance, toughness, and good machinability. The term “pre-hardened” means that the steel will be sold in its hardened and tempered condition to give a working hardness. Thus, there will be no need for further quenching after machining since distortion may occur due to heat treatment. HXM 24 is a trade designation, so the values below are indicative. Confirm them against the supplier’s datasheet and the mill test certificate (MTC) for each lot.

HXM 24 Steel Chemical Composition

Chemistry sets a steel’s hardenability, strength, toughness and machinability. The indicative ranges are:

Element Carbon (C) Chromium (Cr) Manganese (Mn) Molybdenum (Mo) Nickel (Ni) Silicon (Si) Sulphur (S) & Phosphorus (P)
Indicative range (%) 0.35–0.45 1.8–2.0 0.6–1.0 0.3–0.5 0.9–1.2 0.2–0.4 Controlled (limits confirmed on the MTC)
Indicative values only. Confirm against the MTC supplied with your material.

The steel derives its strength from the medium carbon content. The chromium and molybdenum contribute to hardenability and strength while the nickel contributes to toughness, especially for thick sections with unequal cooling.

HXM 24 Steel Mechanical Properties

HXM 24 steel is selected for applications requiring a balance of hardness, strength, toughness and machinability. Its actual mechanical properties depend on the supplied condition, manufacturing process and applicable technical specification.

Property Hardness Tensile Strength Yield Strength Density Modulus of Elasticity Toughness
Indicative Value Supplied pre-hardened. Request the exact HRC range and a hardness test report for your lot Approx. 1,000–1,200 MPa (subject to verification) Approx. 850–1,000 MPa (subject to verification) Approx. 7.85 g/cm³ Approximately 210 GPa Depends on the grade specification and supplied condition

Need HXM 24 Steel for Your Application?

Contact Virat Special Steels for HXM 24 steel supply, availability and technical assistance.

Email Us → Call 98140-21775 WhatsApp

HXM 24 Steel Heat Treatment

Since the HXM 24 alloy comes already hardened, most mold manufacturers may machine and use it straight out of the box. Heating changes hardness, toughness, dimensional stability, and service life; therefore, any other form of heating must be done based on the grade specifications and recommendations by a heat treatment expert.

Any wrong process will result in cracking, warping and wrong properties. Obtain recommended temperatures and cooling methods from the producer datasheet.

Applications of HXM 24 Steel

Plastic injection moulds

Cavities, cores and mould bases where hardness, dimensional accuracy and wear resistance matter.


  • Extrusion tooling and industrial moulding tools
  • Precision tooling selected according to operating conditions.
  • Dies and tooling components
  • Components that need a suitable combination of strength and wear resistance.
  • Automotive and engineering tooling
  • Selected production moulds and precision tooling.

Key Features and Advantages of HXM 24 Steel


  • Ready with pre-hardened materia No heat treatment required post-machining, resulting in reduced processing time and decreased risk of distortion.
  • High hardness and wear resistanceSuited to cavities and components that see repeated cycles.
  • Machinability appropriate to supplied hardness Workable with the right tooling and parameters, although harder than annealed steel.
  • Polishing potentia Excellent finishes can be obtained when cleanliness, microstructure, and process control are ensured.
  • Dimensional stability Supported by sound machining practice and stress relief where needed.
  • Bar formats Flat, square and round bars, subject to availability.

A boundary worth stating. HXM 24 is positioned for mould and general tooling duty. For high-temperature work such as pressure die casting or forging, hot work steels like H13 are the usual choice, and HXM 24’s suitability for hot work service has not been established.

Machinability and Surface Finishing

Machining Pre-hardened steel cuts differently from annealed material. Rigid machines and holders, sharp carbide tooling, steady cooling, and cutting data from your tool maker for the actual supplied hardness all help. Speeds and feeds vary with hardness, tool and operation, so we do not list them here. When EDM work is completed, the layer that has been formed should be stripped off using stone or polishing, since it is tough and brittle.

Polishing and texturing Polishing is influenced by the cleanliness, microstructure of the steel and your desired finish. If you want a bright, optical finish or any highly textured component, please ensure that Virat agrees with the required finish prior to order.

Welding and repair Repair welding will generally require matching filler material along with some pre-heating and tempering after the weld. Please verify this with the supplier and welding professional.

How to Buy HXM 24 Steel in India

Virat Special Steels supplies HXM 24 in flat, square and round bars, subject to stock, with sizes confirmed against customer requirements. With 35+ grades across cold work, hot work, high speed and plastic mould steels, and offices in Gurugram and Ludhiana, the team can help with size selection and availability.

Before you order, have these ready:

For information about HXM 24 steel availability, specifications and supply, contact our team.

Frequently Asked Questions About HXM 24 Tool Steel

Pre-hardened die casting mold and tool steel supplied by Virat Special Steels for plastic molds, extrusion tools, and precision dies that require hardness, wear resistance, and machinability in combination.

Products

 

  • Corporate Office: C-545, Sector-37, Pace City - II, Gurgaon 122001 (Haryana) India
  • UNIT-I: C-146, Focal Point, Phase - V, Ludhiana 141010 (Punjab) India
  • UNIT-II: NH-1, G.T. Road, Opp. Sarita Forging, Rajgarh, LDH (Punjab) India

 

payment